1.5 Centurion - Connect USB Cable - TechnoResearch Manuals

Skip to content

Home
Contact Us
Common Jobs
Manuals
Languages
- Español
- Italiano
- Deutsch
- Français
- Others

Search for:

Home
Contact Us
Common Jobs
Manuals
Languages
- Español
- Italiano
- Deutsch
- Français
- Others

Search for:

Table of Contents

Search for:

Introduction
Main Features
How To Setup TR4 System
All TechnoResearch Cables
Troubleshooting
Common Jobs
Updating Centurion License
- Centurion Super Pro/Plus (Multibike)
- Centurion Audio Pro (Multibike)
- Alaris (Audio Pay-Per-Bike)
- Centurion Pay-Per-Bike (PPB)
Non-Stock ECUs
Connecting via Bluetooth
Victory / Indian Diagnostics
Checking DTCs Manually (HD)
FAIL message When Performing Blank ECU Programming
1. Centurion Setup and Installation
- 1.1 Where to get the Software
- 1.2 Install Centurion
- 1.3 Run Centurion
- 1.4 Insert Security Key into USB Port
- 1.5 Connect USB Cable
- 1.6 Powerup the Centurion
- 1.7 Powerup to Automatically Install Drivers
  - 1.7.1 Location and appearance of Harley-Davidson Diagnostic Connectors
  - 1.7.2 Appearance of Ducati Diagnostic Connectors
- 1.8 Update the Centurion Software
- 1.9 Centurion Disclaimer/Language Selection
- 1.10 Confirm COM Port for Communication
- 1.11 Troubleshooting COM Port Issues
2. Using the Centurion
- 2.1 Connecting to The Motorcycle and Key Features
- 2.2 Centurion – Main Menu
- 2.3 Centurion – Tab Menu
- 2.4 Centurion Toolbar Buttons (For Both Single and Pro Users)
3. Centurion Toolbar Icon Description
- 3.1 Centurion Toolbar Buttons/Commands
- 3.2 Digital Data View
- 3.3 Strip Chart Data View
- 3.4 Meter Data View
- 3.5 Live DTC Monitoring
- 3.6 Active Test
  - 3.6.1 Active Test Definitions
    (Harley Davidson® Delphi)
  - 3.6.2 Active Test Definitions
    (Ducati-Marelli)
- 3.7 Active Settings
  - 3.7.1 Active Settings Definitions
    (Harley Davidson® Delphi)
  - 3.7.2 Active Settings Definitions
    (Ducati-Marelli)
4. Centurion – How to Change Units/Colors
- 4.1 Centurion – How to Change Units
- 4.2 Centurion – How to Change Colors
5. Centurion Super Pro/Audio – Monitor Real-Time Data (Digital Data View)
- 5.1 Monitor Data
- 5.2 Change Channels
- 5.3 Communicate
6. Centurion Super Pro/Audio – Monitor Real-Time Data (Strip Chart Display)
- 6.1 Centurion – View Data
- 6.2 Centurion – Turn Ignition to Run
- 6.3 Centurion – Communication
- 6.4 Centurion – Start Engine
- 6.5 Centurion – Change Channel Data
- 6.6 Centurion – Increasing or Decreasing Channels on the Strip Chart
7. Centurion Super Pro – Harley Davidson Tests and Activations
- 7.1 Centurion – Specific Functions
- 7.2 Centurion – Prepare to Connect
- 7.3 Centurion – Select the Procedure to Perform
- 7.4 Centurion – Selecting A Procedure/ Test
  - 7.4.1 Active Tests
  - 7.4.2 Active Settings
8. Centurion – Specific Functions for Harley-Davidson® Motorcycles
- ECU/ECM
- TSM-TSSM-HFSM-BCM
- INFOTAINMENT
- INSTRUMENTATION
- ABS
  - 8.10 Centurion Super Pro – Abs Bleeding
- TPMS
  - 8.24 Centurion Super Pro – TPMS: Sensor
  - 8.27 Centurion Super Pro – TPMS: SYSTEM
9. Location of Diagnostic Connectors
- 9.1 Harley-Davidson Models
Centurion Glossary

1.5 Centurion - Connect USB Cable

Connect the mini USB or USB cable to the Vehicle Communication Module (VCM)

The module is shown below, with the mini USB port on the left side of the VCM.
Connect the other end to the PC's second USB port.

© 2024 TechnoResearch Manuals. Proudly powered by Sydney

Light

Dark