7.2 Centurion - Prepare to Connect - TechnoResearch Manuals

Skip to content

Home
Contact Us
Common Jobs
Manuals
Languages
- Español
- Italiano
- Deutsch
- Français
- Others

Search for:

Home
Contact Us
Common Jobs
Manuals
Languages
- Español
- Italiano
- Deutsch
- Français
- Others

Search for:

Table of Contents

Search for:

Introduction
Main Features
How To Setup TR4 System
All TechnoResearch Cables
Troubleshooting
Common Jobs
Updating Centurion License
- Centurion Super Pro/Plus (Multibike)
- Centurion Audio Pro (Multibike)
- Alaris (Audio Pay-Per-Bike)
- Centurion Pay-Per-Bike (PPB)
Non-Stock ECUs
Connecting via Bluetooth
Victory / Indian Diagnostics
Checking DTCs Manually (HD)
FAIL message When Performing Blank ECU Programming
1. Centurion Setup and Installation
- 1.1 Where to get the Software
- 1.2 Install Centurion
- 1.3 Run Centurion
- 1.4 Insert Security Key into USB Port
- 1.5 Connect USB Cable
- 1.6 Powerup the Centurion
- 1.7 Powerup to Automatically Install Drivers
  - 1.7.1 Location and appearance of Harley-Davidson Diagnostic Connectors
  - 1.7.2 Appearance of Ducati Diagnostic Connectors
- 1.8 Update the Centurion Software
- 1.9 Centurion Disclaimer/Language Selection
- 1.10 Confirm COM Port for Communication
- 1.11 Troubleshooting COM Port Issues
2. Using the Centurion
- 2.1 Connecting to The Motorcycle and Key Features
- 2.2 Centurion – Main Menu
- 2.3 Centurion – Tab Menu
- 2.4 Centurion Toolbar Buttons (For Both Single and Pro Users)
3. Centurion Toolbar Icon Description
- 3.1 Centurion Toolbar Buttons/Commands
- 3.2 Digital Data View
- 3.3 Strip Chart Data View
- 3.4 Meter Data View
- 3.5 Live DTC Monitoring
- 3.6 Active Test
  - 3.6.1 Active Test Definitions
    (Harley Davidson® Delphi)
  - 3.6.2 Active Test Definitions
    (Ducati-Marelli)
- 3.7 Active Settings
  - 3.7.1 Active Settings Definitions
    (Harley Davidson® Delphi)
  - 3.7.2 Active Settings Definitions
    (Ducati-Marelli)
4. Centurion – How to Change Units/Colors
- 4.1 Centurion – How to Change Units
- 4.2 Centurion – How to Change Colors
5. Centurion Super Pro/Audio – Monitor Real-Time Data (Digital Data View)
- 5.1 Monitor Data
- 5.2 Change Channels
- 5.3 Communicate
6. Centurion Super Pro/Audio – Monitor Real-Time Data (Strip Chart Display)
- 6.1 Centurion – View Data
- 6.2 Centurion – Turn Ignition to Run
- 6.3 Centurion – Communication
- 6.4 Centurion – Start Engine
- 6.5 Centurion – Change Channel Data
- 6.6 Centurion – Increasing or Decreasing Channels on the Strip Chart
7. Centurion Super Pro – Harley Davidson Tests and Activations
- 7.1 Centurion – Specific Functions
- 7.2 Centurion – Prepare to Connect
- 7.3 Centurion – Select the Procedure to Perform
- 7.4 Centurion – Selecting A Procedure/ Test
  - 7.4.1 Active Tests
  - 7.4.2 Active Settings
8. Centurion – Specific Functions for Harley-Davidson® Motorcycles
- ECU/ECM
- TSM-TSSM-HFSM-BCM
- INFOTAINMENT
- INSTRUMENTATION
- ABS
  - 8.10 Centurion Super Pro – Abs Bleeding
- TPMS
  - 8.24 Centurion Super Pro – TPMS: Sensor
  - 8.27 Centurion Super Pro – TPMS: SYSTEM
9. Location of Diagnostic Connectors
- 9.1 Harley-Davidson Models
Centurion Glossary

7.2 Centurion – Prepare to Connect

Turn ON the ignition switch and make sure the engine stop/run switch is in the RUN position.

© 2024 TechnoResearch Manuals. Proudly powered by Sydney

Light

Dark