Table of Contents
- Introduction
- Main Features
- How To Setup TR4 System
- All TechnoResearch Cables
- Troubleshooting
- Common Jobs
- Updating Centurion License
- Non-Stock ECUs
- Connecting via Bluetooth
- Victory / Indian Diagnostics
- Checking DTCs Manually (HD)
- FAIL message When Performing Blank ECU Programming
- 1. Centurion Setup and Installation
- 1.1 Where to get the Software
- 1.2 Install Centurion
- 1.3 Run Centurion
- 1.4 Insert Security Key into USB Port
- 1.5 Connect USB Cable
- 1.6 Powerup the Centurion
- 1.7 Powerup to Automatically Install Drivers
- 1.8 Update the Centurion Software
- 1.9 Centurion Disclaimer/Language Selection
- 1.10 Confirm COM Port for Communication
- 1.11 Troubleshooting COM Port Issues
- 2. Using the Centurion
- 3. Centurion Toolbar Icon Description
- 4. Centurion – How to Change Units/Colors
- 5. Centurion Super Pro/Audio – Monitor Real-Time Data (Digital Data View)
- 6. Centurion Super Pro/Audio – Monitor Real-Time Data (Strip Chart Display)
- 7. Centurion Super Pro – Harley Davidson Tests and Activations
- 8. Centurion – Specific Functions for Harley-Davidson® Motorcycles
- ECU/ECM
- 8.1 Centurion Super Pro/Audio – Read And Clear DTCS
- 8.2 Centurion Super Pro – Speedometer Calibration
- 8.6 Centurion Super Pro – Air Fuel Value (AFV)
- 8.7 Centurion Super Pro – Idle Adjustment
- 8.8 Centurion Super Pro – Blank ECU Programming
- 8.9 Centurion Super Pro – Blank Ecu Programming (Clone)
- 8.11 Centurion Super Pro – Module Replacement (4-Pin Models)
- 8.12 Centurion Super Pro – Module Replacement (6-Pin Models)
- 8.13 Centurion Super Pro – ECU: (Enable/Disable)
- 8.17 Centurion Super Pro – Fuel Tank Drain
- 8.18 Centurion Super Pro – Compression Test
- TSM-TSSM-HFSM-BCM
- 8.3 Centurion Super Pro – Hands Free Keyfob Programming
- 8.4 Centurion Super Pro – Keyfob Disabling (Hands Free Fob Only)
- 8.5 Centurion Super Pro – Program Personal Identification Number (Pin) / Personal Key Code
- 8.19 Centurion Super Pro – BCM: (Enable/Disable)
- 8.20 Centurion Super Pro – BCM-Lights: (Enable/Disable)
- 8.22 Centurion Super Pro – Unlocking A Security Module
- 8.23 Centurion Super Pro – Security: Push Button Fob Manual Programming
- INFOTAINMENT
- INSTRUMENTATION
- ABS
- TPMS
- ECU/ECM
- 9. Location of Diagnostic Connectors
- Centurion Glossary
9.1 Harley-Davidson® Models
- Softail Models
-
2001 - 2017 Softail: Located UNDER the seat*, attached to the frame by the rear fender. Plug is grey in color, with black rubber plug installed.
*Requires removing the seat
2018 - 2021 Softail: Located on the LEFT side of the motorcycle, behind the side cover.
- Dyna Models
- All Dyna's: Located on the LEFT side behind the cover below the seat. Connector is light grey in color with black rubber plug installed.
- Sportster Models (includes XR Models)
- 2007 - 2020 Sportster: Located behind the LEFT side cover. Plug is Grey in color with black rubber plug installed.
- V-Rod Models
-
All V-Rod's: Located behind the LEFT or RIGHT front frame cover.
*Plug is grey in color with black rubber plug installed.
*Tools are required to remove the cover. - Touring Models
-
2001 - 2007 Touring: Located behind the RIGHT hand side cover.*Plug is grey in color with black rubber plug installed.
*Accessible by removing the RIGHT side saddle bag.2008 - 2020 Touring: Located behind the LEFT hand side cover.
*Plug is grey in color with black rubber plug installed.
*Accessible by removing the LEFT side saddle bag. - Street Models
-
2015 - 2020 Street: Located behind the RIGHT hand side cover.
*Plug is grey in color with a black rubber plug installed.