8.3 Change Visible Parameters - TechnoResearch Manuals

Skip to content

Home
Contact Us
Common Jobs
Manuals
Languages
- Español
- Italiano
- Deutsch
- Français
- Others

Search for:

Home
Contact Us
Common Jobs
Manuals
Languages
- Español
- Italiano
- Deutsch
- Français
- Others

Search for:

Table of Contents

Search for:

DirectLink Introduction
DirectLink Main Features
How To Setup TR4 System
About This Manual
Troubleshooting
TRo2/o2 Sensors/Rivnut Installation
O2 Sensor Installation Kit Lite
ECU Tuning Compatibility
All TechnoResearch Cables
Tuning Victory® Motorcycle
Licensing
- Flashing with a USB License
- Tuning Adding with Digital License
- Flashing with a Maximus
1 Setup and Installation
- 1.1 Where To Get The Software
- 1.2 Install Direct Link Flash Tuner
- 1.3 Run Direct Link Flash Tuner
- 1.4 Connect USB Cable
- 1.5 Power Up The Direct Link Flash Tuner
- 1.6 Power Up To Automatically Install Drivers
- 1.7 Update The Software
- 1.8 Confirm Com Port For Communication
- 1.9 Troubleshooting Com Port Issues
2. Toolbar Menu and Icon Descriptions
- 2.1 Direct Link – Main Menu
- 2.2 Direct Link – Tab Menu
- 2.3 Direct Link – Toolbar Buttons
3. Direct Link – Key Features
- 3.1 Direct Link – Creating a Backup
- 3.2 Loading a Map
- 3.3 Additional Checks
- 3.4 Choosing an AFR Mode
- 3.5 Direct Link – Programming
- 3.6 Direct Link – Application Version
4. Direct Link – Important Tables
- 4.1 VE Table
- 4.2 Spark Table
- 4.3 AFR Ratio Table
- 4.4 Cranking Fuel
- 4.5 Idle Table
- 4.6 IAC Table
- 4.7 Acceleration Table
- 4.8 Decell (Deceleration) Table
- 4.9 Closed Loop
- 4.10 Warm Up Fuel Table
5. Program the Calibration into the ECU
- 5.1 Save Original Calibration
- 5.2 Programming Status
6. How to Save the Modified Calibration
- 6.1 Save As
- 6.2 Calibration Information
7. How to Change Units and Colors
- 7.1 Changing Units
- 7.2 Changing Colors
8. Monitor Real-Time Data
(Gauges/Meter Display)
- 8.1 Monitor Data
- 8.2 Change Channels
- 8.3 Change Visible Parameters
- 8.4 Turn Ignition to Run
- 8.5 Communicate
9. Monitor Real-Time Data
(Strip Chart/Meter Display)
- 9.1 View Data
- 9.2 Change Channels
  - 9.2.1 Channel Display
- 9.3 Turn Ignition to Run
- 9.4 Communicate
10. Auto-Mapping
- 10.1 Select Strip Chart
- 10.2 Logging Data with A Dyno
- 10.3 Logging Data with Mobile Dyno
11. Common Issues and
Possible Solutions
- 11.1 Tuning File Issues
- 11.2 Fuel Issues
- 11.3 Issues with Auto Mapping Sessions Result
- 11.4 Idle Issues
- 11.5 Backup and Restore
  - 11.5.1 Why Should I Make a Backup?
  - 11.5.2 I Can’t Find the Backup I Made
- 11.6 Oxygen Sensor Issues
- 11.7 Other Possible Drivability Concerns
  - 11.7.1 MAP Sensor Failing
- 11.8 ECU Programming Issues
  - 11.8.1 Flashing 2001 to 2004 Issues
- 11.9 Deceleration Popping
  - 11.9.1 Deceleration Popping Causes
  - 11.9.2 Deceleration Popping Potential Fixes
Glossary

8.3 Change Visible Parameters

There are six channels. Click the gray square button to change the visible parameter or select 'Default'.

Direct Link Channel View Mode

Customize any parameters to display. Click 'OK'.

Direct Link Gauges Channels Mode Parameters

© 2024 TechnoResearch Manuals. Proudly powered by Sydney

Light

Dark